;{CR10X} *Table 1 Program 01: 60.0000 Execution Interval (seconds) 1: Temp (107) (P11) 1: 1 Reps 2: 1 SE Channel 3: 1 Excite all reps w/E1 4: 1 Loc [ _________ ] 5: 1 Multiplier 6: 0 Offset 2: Pulse (P3) 1: 1 Reps 2: 1 Pulse Channel 1 3: 21 Low Level AC, Output Hz 4: 2 Loc [ _________ ] 5: .098 Multiplier 6: 0 Offset 3: Excite-Delay (SE) (P4) 1: 1 Reps 2: 5 2500 mV Slow Range 3: 2 SE Channel 4: 2 Excite all reps w/Exchan 2 5: 2 Delay (0.01 sec units) 6: 2500 mV Excitation 7: 7 Loc [ _________ ] 8: .142 Multiplier 9: 0 Offset 4: Pulse (P3) 1: 1 Reps 2: 2 Pulse Channel 2 3: 2 Switch Closure, All Counts 4: 3 Loc [ _________ ] 5: .1 Multiplier 6: 0 Offset 5: Batt Voltage (P10) 1: 28 Loc [ _________ ] 6: Internal Temperature (P17) 1: 27 Loc [ _________ ] 7: If time is (P92) 1: 0 Minutes (Seconds --) into a 2: 60 Interval (same units as above) 3: 10 Set Output Flag High (Flag 0) 8: Real Time (P77)^17480 1: 1220 Year,Day,Hour/Minute (midnight = 2400) 9: Average (P71)^26702 1: 2 Reps 2: 1 Loc [ _________ ] 10: Wind Vector (P69)^15628 1: 1 Reps 2: 0 Samples per Sub-Interval 3: 1 S, theta(1) with polar sensor 4: 2 Wind Speed/East Loc [ _________ ] 5: 7 Wind Direction/North Loc [ _________ ] 11: Maximum (P73)^14070 1: 1 Reps 2: 0 Value Only 3: 2 Loc [ _________ ] 12: Sample (P70)^8276 1: 1 Reps 2: 7 Loc [ _________ ] 13: Totalize (P72)^19531 1: 1 Reps 2: 3 Loc [ _________ ] 14: Average (P71)^10204 1: 2 Reps 2: 27 Loc [ _________ ] 15: If Flag/Port (P91) 1: 51 Do if Port 1 is Low 2: 30 Then Do 16: Serial Out (P96) 1: 71 Storage Module 17: End (P95) 18: If (X<=>F) (P89) 1: 3 X Loc [ _________ ] 2: 2 <> 3: 0 F 4: 30 Then Do 19: Do (P86) 1: 10 Set Output Flag High (Flag 0) 20: Real Time (P77)^16608 1: 1210 Year,Day,Hour/Minute (Same as 1220) 21: Sample (P70)^29000 1: 3 Reps 2: 1 Loc [ _________ ] 22: End (P95) *Table 2 Program 01: 60.0000 Execution Interval (seconds) 1: Set Port(s) (P20) 1: 9999 C8..C5 = nc/nc/nc/nc 2: 9997 C4..C1 = nc/nc/nc/output 2: If time is (P92) 1: 1 Minutes (Seconds --) into a 2: 60 Interval (same units as above) 3: 30 Then Do 3: If (X<=>F) (P89) 1: 28 X Loc [ _________ ] 2: 4 < 3: 12.2 F 4: 21 Set Flag 1 Low 4: If (X<=>F) (P89) 1: 28 X Loc [ _________ ] 2: 3 >= 3: 12.1 F 4: 41 Set Port 1 High 5: End (P95) 6: If time is (P92) 1: 721 Minutes (Seconds --) into a 2: 1440 Interval (same units as above) 3: 41 Set Port 1 High 7: If Flag/Port (P91) 1: 21 Do if Flag 1 is Low 2: 30 Then Do 8: If time is (P92) 1: 5 Minutes (Seconds --) into a 2: 60 Interval (same units as above) 3: 51 Set Port 1 Low 9: End (P95) *Table 3 Subroutines End Program -Input Locations- 1 _________ 1 2 1 2 _________ 1 4 1 3 _________ 1 3 1 4 _________ 0 0 0 5 _________ 0 0 0 6 _________ 0 0 0 7 _________ 1 2 1 8 _________ 0 0 0 9 _________ 0 0 0 10 _________ 0 0 0 11 _________ 0 0 0 12 _________ 0 0 0 13 _________ 0 0 0 14 _________ 0 0 0 15 _________ 0 0 0 16 _________ 0 0 0 17 _________ 0 0 0 18 _________ 0 0 0 19 _________ 0 0 0 20 _________ 0 0 0 21 _________ 0 0 0 22 _________ 0 0 0 23 _________ 0 0 0 24 _________ 0 0 0 25 _________ 0 0 0 26 _________ 0 0 0 27 _________ 1 1 1 28 _________ 1 3 1 -Program Security- 0000 0000 0000 -Mode 4- -Final Storage Area 2- 0 -CR10X ID- 0 -CR10X Power Up- 3 -CR10X Compile Setting- 3 -CR10X RS-232 Setting- -1 -DLD File Labels- 0 -Final Storage Labels- 0,Year_RTM,17480 0,Day_RTM 0,Hour_Minute_RTM 1,{AT_AVG~1,26702 1,{WS_AVG~2 2,{WindVectorS_WVT~2,15628 2,{WindVectorD1_WVT~7 3,{WS_MAX~2,14070 4,{WD~7,8276 5,{P~3,19531 6,{Panel_temp~27,10204 6,{Battery~28 7,Year_RTM,16608 7,Day_RTM 7,Hour_Minute_RTM 8,_________~1,29000 8,_________~2 8,_________~3